HTML5 conformanceBest viewed with a Web browser.
Shandon Cytospin 2 Serial number 3030? Providence 302297, St. Paul's 86-26330 A 2003-09-24 Measured run-out on side of drive boss, 0.003" at top, 0.0025" at bottom. Engaged loose connectors in base of chassis. Seal on motor shaft, V-RING 75 V8A PAT. 2010-10-12 Reseated faston connectors again. Next time there is a fault these connectors should be tightened or replaced.
Classification according to Jim S. Numbers 201-400, Computers & Office Equipment.00082 Welch Vacuum pump, Model 1400B80, Serial no. 151083. Chemistry tag 12883. LSc tag 02939.
00011 Zeiss Fourescent Illuminator for Photomicroscope 2. 2002-10-18 Shortened white power cable to repair broken conductors. 2007-11-16 Overhauled power switch.
00066 Makita Model 4300D, serial no. 021750E. 2003-04-01 Installed new motor; part number 629581-1, 44.80$.
00068 MW Universal AC-CD adaptor. Model MW70UC. 2003-10-21 Loaned to Mike N. for illuminator.
00069 Luxo lamp stored by James M.
00070 Burton lamp stored by James M.
00071 Breathing chambers for 5 r a t s. Tag is on manifold base. Five holders rest in place. 2004-10-15 Sold do I. L., Pharmacology.
00072 Breathing chambers for 5 r a t s. Tag is on manifold base. Five holders rest in place. 2004-10-15 Sold do I. L., Pharmacology.
00073 Breathing chambers for 5 r a t s. Tag is on manifold base. Five holders rest in place. 2004-10-15 Sold do I. L., Pharmacology.
00074 Breathing chambers for 5 r a t s. Tag is on manifold base. Five holders rest in place. 2004-10-15 Sold do I. L., Pharmacology.
00075 Water manometer and volumetric manometers on wood base. 2005-01-13 In use by Jody W.
00076 Radiometer Copenhagen Hemoximeter. 2005-01-26 Loaned to Issy L., including large manual, summary leaflet, accessory kit, one box of tubes, 4 boxes of reagent vials, 2 bottles of cleaning solutions.
00077 Haake FE thermostatted water circulator. Serial no. 78096. 2004 Replaced 470 microfarad capacitor and TCA280B control IC. Still not working. 2005-02-10 Replaced 2.7 kohm resistor. Still not working. 2006-09-07 Fixed connections on triac and installed another new TCA280B. 2006-09-28 Reassembled & tested. Still not working. The voltage on the gate of the Triac is not changing when the thermal switch changes state. Seems that one of the resistors or caps was toasted when the triac was mis-connected or that the new TCA280B made by IES differs from the Phillips which the circuit was designed around. Draw a decent schematic, check all the resistors & caps and understand the circuit design well enough to recognize why it isn't working. The schematic in the Haake FE manual in the filing cabinet is almost legible. The TCA280B which might have been damaged by having the gate connected to "B" (yikes!) has a fragment of tape on top marked 1. The second replacement TCA280B is unmarked. Shelve this project until there is time to burn (dream on).
00078 Sartorius balance Type 1475 MP8-2, Fabr. no. 3308010 OPI 553 459 2004-12-?? Plastic mounting pin on bottom of pan broken. 2005-08-10 New acrylic pin turned and attached to pan with Shoe Goo. Balance returned to Jaky C.
00079 Sartorius balance Type B 310P, Fabr. no. 40010126 2005-04-29 Output not stable. Grounding leaf on bottom of pan was inverted and possibly contacting the case. Reinstalled leaf correctly and balance is now stable.
00080 Microsoft IntelliMouse 1.2A PS/2 Compatible.
00081 Microsoft Serial Mouse 1436354.
2002-06-15 switch and belt replaced. 2004-11-04 Complete rebuild including new check valve leaf. 2005-05-25 Seized. Dismantled and cleaned. 2005-10-28 Overhaul completed. 2006-03-06 Seized after approximately four months of service.This is the second stage of the pump after overhaul. Residue, in the journal bearing at the blind end of the shaft and adjacent to the post where the cover for the outlet leaf valve attaches, was significant in stopping operation.
2006-03-09 Overhaul completed. Testing in service.
00083 Welch Vacuum pump, Model 1400B80, Serial no. 172392. 2004-10 Inherited from basement of Detwiller. 2005-05-19 cleaned and operated momentarily; appears to have seen little use. Taken to LSc. 2006-08-11 Dismantled, cleaned, ... 2006-10-28 Reassembly and testing completed, returned to service.
00086, UBC 0202210 Revco -80 C freezer, Model ULT1786-5-AUA 2005-09-09 Replacment backup battery from Main Electronics.
00087 Thermolyne Maxi Mix, Model M-16715, Serial 26812722. 2005-09-21 Replaced broken spring wires, 3+1/8" long. 2006-03-22 Replaced broken spring wire. 2007-03-30 Replaced broken spring wire.
00088 Thermolyne Maxi Mix, nameplate absent. 2005-09-22 Replaced worn out balance link, insulated shorted wire. 2006-03-22 Replaced broken spring wire. 2007-03-30 Motor winding burned. Shelve for parts.
00089 Clay Adams Sero-Fuge II Centrifuge, Serial No. 126316, Cat. No. 0541.
Inherited from VGH.
2005-10-20 Replaced Pyle-National Strateline EPD51532 plug with Hubbell HBL5965VYCN. Used by BMLSc.
00090 Aluminum box, 12 x 12 x 6, for use of UV light in Brooks Lab. 2005-11-25 Completed.
00091 Varian Rotary Vacuum Pump. CD-200 Varian IPO Serial No. 106441, Part No. 0441P1411.30 Motor: Franklin Electric 115/230 V. 2006-01-11 Motor connected for 115 V. Sent to duty in J.K. Laboratory.
00092 Amicon Centrilutor Model 57005 (Micro-electroelutor) 2006-01-12 Donated to Goods for Cuba.
00093 AO Spencer Lamp, Catalog Number 735 2006-03-16,17 Replaced cord and switch. Washed tilt adjusting screw and rack & pinion focus with solvent. Dismantled and cleaned optics. Tested. Adjusted mirror.
00094 Sola Constant Voltage Transformer Cat. No. 23-25-210 Type: CVS Rated 1000 VA Input Volts: 115 / 208 / 230, 1 Phase Output: 118 V x 8.46 A, 236 V x 4.23 A
00095 Fi-stream 4 l/hr Glass Still Serial No. 8649-10B Heaing element, 240 v, 1500 W, price at 2006-03, $579.10
00096 VGA video cable, M-M, ~12' 2006-06-02 loaned.
00097 VGA video extension cable, M-F, 6' 2006-06-02 loaned.
00098 USB extension cable, M-F, 12' 2006-06-02 loaned.
00099 Nickel plated luggage dolly 2006-07-08 lent to Katherine S.
00100 Black Samsonite luggage dolly 2006-07-15 lent by Gail M.
000?? Fi-stream 8 l/hr Glass Still Serial No. 82-08-079 Heaing element, 240 v, 1500 W, price at 2006-03, $579.10
00106 HP 3325A Synthesizer/Function Generator. 2002 09 23 Salvaged from renovated area on floor 1. 2002 10 01 Indefinite loan to Eng. Phys. Project Lab. (H. Davis).
00107 Kysor saw. Back guide bearings for blade are NDH 77503, shielded, 17 mm x 40 mm x 12 mm wide. Current number is 6203 2RS (2 rubber seals). Commonly used; about 5 $ each at 2004-03-03. 2004-03-03 Make new throat plate. Clear lower guide bearing in kerosine.
00108 Cole-Parmer 9x9 stirrer. 2005-01-06 frozen bushings cleaned in kerosine and reassembled, still noisy, new bushings machined and installed; 2005-01-28 returned to Jayachandran;
00109 Cole-Parmer 9x9 stirrer. 2004-09 salvaged from Psych. stairwell storage area; 2005-01-07 in custody of Jayachandran;
00110 Branson sonicater. 2006-08-21 reported to be not working & delivered to shop; There was evidence of moisture on lower p.c.b. Cleaned. 2006-09-01 3 A fuse replaced and returned to service; Components on power board R1 101.7 ohms. R2 101.5 ohms. Q1 OK on transistor tester. Q2 OK on transistor tester. D1 20 ohms forward, infinite resistance in reverse. D2 20 ohms forward, infinite resistance in reverse. D3 20 ohms forward, infinite resistance in reverse. D4 20 ohms forward, infinite resistance in reverse. D5 25 ohms forward, infinite resistance in reverse. D6 25 ohms forward, infinite resistance in reverse. D7 25 ohms forward, infinite resistance in reverse. D8 25 ohms forward, infinite resistance in reverse. Components on digital control board MC7805C voltage regulator. TLC271 CP programmable low power operational amplifier. 74HC14 hex inverting Schmidt trigger. 74HCT04 hex inverter. C3 C4 C8 C9 C10 C14
00111 Labline Pyro-Magnestir. 2006-09-07 New cord & plug needed; 2006-09-14 Dismantled, cleaned, cord & plug replaced, reassembled, returned to service in D.B. laboratory;
00112 Labline Magnestir. 2005-2006 Discarded to shop; 2006-09-22 Dismantled, cleaned, cord & plug replaced, reassembled, returned to service in D.B. laboratory;
00116 Whirlpool Ice Maker 2005 Purchased new. 2007-05-02 Problem with ice production reported. Drain cap on the water pan was loose. Routine cleaning according to the _Use & Care Guide_ should be reviewed and performed if necessary.
00117 Labconco Tissue Culture Enclosure 2007-05 Located in G165. 2007-05-09 Installed UV germicidal flourescent bulb, G30T8; Media Group, $CA18. 2007-05-24 Replaced power cord.
00118 MISCO benchtop microcentrifuge Label reads "MISCO Microchemical Specialties Co. 1825 Eastshore Hwy., Berkeley, Calif. Made in U.S.A. Mod. 115 v 2.3 a Ser. 60 CPs" http://carnot.yi.org/MISCOcentrifuge.jpg 2007-06-08 Attempted unsuccessfully to measure speed with digital tachometer. 2007-06-14 Donated to GFC.
00119 Bio-Rad Model 500 Power Supply, Serial No. 28BR1445. This is the same model as tag number 00679. These machines limit voltage and current; the most restrictive of the two settings limits the output. For voltage controlled output, the current knob is fully clockwise. For current controlled output, the voltage knob is fully clockwise. The shorting jumper is only for warmup under current control. DO NOT SHORT THE OUTPUT OTHERWISE! Operating instructions are available on the Web. Open http://www.bio-rad.com/. Search for "power 500". At the target page scroll down to Bulletin 9037 which is a scan of the paper manual for a model similar to the 500. ca. 1992 Inherited machine from R.H.P. 2004-09-08 Circuitry and components checked by J.M. Replacement IC MC1466L could not be found. 2007-07-31 J.T. reports no output against gel. 20 microF 600 V capacitor and power cord replaced. Works OK. Please follow the Bio_Rad instructions, P.E.
00120 Fisher Water-Jacketed Incubator model 511, serial no.: 10BA-3. The user manual is in the top drawer of the lateral cabinet in G218. 2008-01-03 Displayed temperature was approximately 2C high. Calibrated. 2008-01-04 Opened CO_{2} line, adjusted the setting to 5%, equilibrated and checked with Fyrite. Within reading accuracy of 5%.
00180 Fisher/Spectronics model FB-UVXL-1000 crosslinker, serial no.: 867777 2013-06-20 .
00232 HP Laserjet III model 33449A, serial no.: 2945J61150 2006-03-31 Fault in paper feed reported by C.P. Check gear train.
00274 Allied Telesis CentreCOM 3612TR 10baseT hub. 2004-02-23 Removed from JJ's office and working in shop.
00282 486 PC with VGA and CD drive, named FAC2. 2001-08 24 located in office. 2001-08 24 Video not working. 2001-08 28 Swapped video cards. Worked fine. Replaced original card. 2001-09 07 Installed lock washers on mounting screws of connectors, disconnected 3rd serial ribbon cable and fastened inside chassis, checked for conflict between serial ports and modem. 2001-11 22 Sent to Research Pavillion for use by Niamh K.
00311 AST Premmia 90 Model 733W GXP/90, Serial 501457-501
00312 AST Keyboard P/N 120077-101, Serial B1533460
00313 Hewlett Packard ScanJet IIcx, Model C2500A, Serial 3414A90231
00314 Hewlett Packard DeskJet 560c Printer, Model C2168A, Serial US49N1G0D7
00315 AST Vision 7L, CMC 1701M2 Model 501325-009, P/N: 501325-009 Sub P/N: 230697-002B, Serial 4071600241. 2004-03-18 stored by Hsin. 2004-12-22 returned. 2005-05-18 Failure of high voltage supply. Part no longer available. 2005-05-26 Scrapped.
00316 Pioneer Autoscan Bar Code Reader, Model UCV100BC
00317 IBM laptop, Model 755CE, Type 9545-7BE, Serial 78-466MZ 2002 07 14 Broken plastic bits originally retaining the modular power connector removed (pathetic flimsey design). Two bolts installed to hold power connector against case. Nylon thimbles turned to hold heads of three screws which hold case of power supply together. 2002 07 15 Memory test on startup reports a problem about 32 MB. C.R. pulled and reseated the 32 MB module and subsequently the problem is gone. The machine now in the custody of H.D.
00318 Toshiba Satellite T2100 laptop computer, serial 06514834H Purchased from PC Galore by P. E. This is really a personal machine but is occasionally used at UBC.
00319 HP Laserjet III model 33449A, serial no.: 3031J22206 This machine belongs to Medical Genetics. 2002 07 14-15 All I could find wrong with this machine is that it needs a fresh toner cartridge. It is back in custody of Jeanette.
00320 Seanix 14" VGA monitor; 2002 08 22 Stored by Jen C.
00321 Swingline Electric Stapler, Model No. 67, serial AA501365 2002 08 22 Hammer was sticking in down position. Roland Porter reports that Swingline no longer supports this model and the representative offers no suggestion for repair. Deburred tip of hammer with fine stone and lubricated moving parts. Operates moderately well.
00322 chair 2002 10 03 located in Taylor Fidler Theater.
00323 chair 2002 10 03 located in JP3, 350C.
00324 chair 2002 10 03 located in JP3, Residents Room.
00325 chair 2002 10 03 located in JP3, Residents Room.
00326 chair 2002 10 03 located in JP3, Residents Room.
00327 chair 2002 10 03 located in JP3, Residents Room.
00328 chair 2002 10 03 located in JP3, Residents Room.
00329 chair 2002 10 03 located in JP3, Residents Room.
00330 chair 2002 10 03 located in JP3, 350C.
00331 chair 2002 10 03 located in JP3, 350C.
00332 General Binding Corporation, GBC IM2000 2002 10 04 Jambed with fragments of plastic and paper in die. Disassembled, cleaned, comb straightened, lubricated and reassembled. 2002 10 04 located in stationary storage.
00333 Copper & teak desk lamp. 2002 10 08 stored off site.
00334 IBM 2621 S/N AA-FHDDZ 00/03 fixed disk model DARA-212000 12.07 GB. This machine has the broken external video port. 2003-04-07 Swapped fixed disk with 00335.
00335 IBM 2621 S/N AA-FRKDL 00/05 fixed disk model DARA-212000 12.07 GB. Intermittent boot failure observed. 2003-04-07 Swapped fixed disk with 00334 for test.
00336 LOGiTECH (Logitech) MouseMan(TM), Serial-MousePort M/N: M-CJ13 2003-10-02 Repaired and tested. The black conductor was broken where it enters the mouse. This is the structure of the cable. 9 pin serial connector--insulation color--connector in mouse
casing--(heat shrink/bare/heat shrink)--6 1--green--8 2--black--2 3--red----4 4--orange-5 5--white--1 6--not connected 7--brown--3 8--yellow-7 9--violet-9
00337 HP Laserjet III model 33449A, serial no.: 3140A09717 Donated from another site or department. 2004-01-16 Replaced bronze bushing supporting end of centrifugal fan rotor in AC power supply.
00338 SparcStation 2 Model 147, Serv. code: 4/75, Part No.: 116F3373 Date: 24-apr-91. Power supply Model: CR-81, Part No.: 300-1038-04, Serial no.: 218919. Bearings in fan: 3 mm ID x 8 mm OD x 4 mm W, metal shields. 2004-03-26 Intermittently, fan is very noisy. After front and rear bearings are exchanged, much quieter.
00339 Viewsonic Monitor EF70, Model No. VCDTS21529-1D, S/N 20K000602877 2004-04-20 Not responding to control buttons on bezel. Some video modes yield a black screen. 2004-09-24 Function chip and 2 capacitors replaced by West Broadway T.V. & Video Ltd.
00412 Old 12" monitor, S/N ?? 2008-03-05 Traded to A.L. for ViewSonic PF775
00416 Tube spinner marked DEB 2008-08-31 Overhauled and cleaned.
00520 Cornelius Ice Maker model WC-300-SS-MH, serial no.: HB5490. This machine is in the shared instrument room. 2002 07 24 Ice bridge too thick to break when the plate drops into the chute. Resistance of the evaporator thermocouple measures 2410 Ohms; should be 2815 +/- 10%. 2002 07 24-26 Adjusted potentiometer to reduce the thickness of the ice bridge. Cricuit Board 161456037 368.23 $ Sensor 161456002 51.43 $ 2002 08 09 Installed new circuit board. Ice production is normal again. Water pump leaks and needs service. 2002 08 18 or 19 circuitry shut down. Seems that an ice plate jammed in the chute or there is a problem in the refrigeration cycle. New sensor installed. Working again but harvest still fails occasionally? 2003 03 07 Observed several cycles. Two manual harvest activations sometimes needed to free ice. 2003-11-26 Harvest is failing more frequently. Dan in Tech Support at Mason City said that this failure is usual in a machine of such an age. With time the evaporator surfaces corrode and wear. Surface roughness impedes the ice from falling free. He recommended rotating the machine a few degrees counter clockwise and applying a thin film of lubricant to the evaporator surface. Also check that cooling water is not running through the heat exchanger during the harvest. This will lower the hot gas temperature and further slow the harvest. With monitoring for stuck ice and powering down at night the machine can probably be kept in service for another year. 2003-12-10 Replacement Evaporator will cost about 1800$ + shipping + ~$400 installation = ~2300$.
Replacement machine, complete, f.o.b. Vancouver XWC 322 B322AP $3461 The first 322 means 300 series, 22" wide. The second 322 means 300 pound storage, 22" wide; poly bin stores about 300 pounds.
XWC 330 B430AP $3461 330 means 300 series, 30" wide. 430 means 400 pound storage, 30" wide.
These two models have the same machinery; the bins vary in width. Add about 300 dollars for a s.s. bin. The new machine has a 5 year warranty on compressor, evaporator and printed circuit board. More information on fax pages.
00521 HP Oscillographic Recorder, Model 7402A-002, serial 1402A00861 2002 01 Salvaged from audiology lab. for use by B.M.L.Sc. 2002 07 26 2ndary synchronous belt found to be completely perished. 1st sprocket of 2ndary belt: 70 teeth, 2nd sprocket: 42 t. Belt length measured by tensioned wire: 440-450 mm. Ref. Machinery's Handbook, pl. 2412. This is an MXL belt. Length appears to be designation 180, 225 teeth. 2002 machine scrapped.
00522 Clay Adams Microhematocrit Centrifuge, Cat. No. CT-3400, Serial No. AC25255. 2002-09-14 Bearings in motor expired. 2002-09-16 Old bearings turned out in lathe, bearing holders adapted for fastening with screws, new bearings machined and installed. 2002-09-26 New brushes trimmed and installed.
00523 Clay Adams Microhematocrit Centrifuge, Cat. No. CT-3400, Serial No. AC-18283. 2002-09-14 Commutator turned. Bearings cleaned. Reassembled.
00524 Sorvall MC12V Centrifuge, Serial No. 9205147.
00525 Precision Scientific Tube Shaker inherited from Ann A. U of I item no. 296855. 2003-05-28 Replaced bearings in top spindle, cleaned housing, replaced rubber mat on base. Returned to BMLSc.
00526 IEC MicroMax S.N. 24983067, Manufactured 1995. 2004-07-09, arbor of door latch solenoid lubricated.
00527 Beckman Microfuge B, SER 7772, Manufactured 1995. 2000 This machine was not working and in the shop. 2003-01-.., Repaired by R.M.. and returned to Dana D.'s lab. 2004-08-25 Loaned to BMLSc in preparation for move to new Biology Building.
00528 Thermolyne Maxi Mix, Model M16715, Serial 26849013. 2008-09-03 Tightened loose setscrew on flyweight. Sent to use in L.Sc., 4450, J.J.
00529 IEC Centrifuge, Model CL3R, Serial 37550222. 2008-09-16-23 With power disconnected, rotor does not spin freely. The 3 resistances through the motor are each 1-2 ohms. During attempted startup, there are two pulses of 50 V to the motor. Manual rotation of the shaft gives ~5 V pulses on the tachometer pins. Test pin marked 15 VDC has 15 V. (Replacement motor & boot kit from IEC, $1498.) Reconstructed bent fingers and cracked tube of rotor quick-mount adapter; replaced upper shielded bearing in motor with sealed bearing, SKF 6002-2RSH/C3. Retaining rings removed and replaced with Proto 375. 2008-10-17 Checked speed with ?? tachometer. Front panel agrees with ?? at 500, 700 and 1000 rpm.
00529 VortexGenie mixer, Model K-550-G, Serial 36423. 2008-10-16 Made an aluminum adapter to attach new rubber cup to original UNC 10-24 thread. Used in B.M.L.Sc.
00606 Bio-Rad Conductivity Meter 2001-February, Op. Amp. A1 replaced to restore change of scale; 2001-February, Cap. C8 replaced to restore gain;
00631 Fisher Recordall Series 5000, Omniscribe Model B5237-5I. 2001-June, Capacitor C30, 100 microf in ch. 2 power supply filter replaced; jitter cured. Mylar ribbons removed and cleaned; wear noted. Positions of stainless rods in frame adjusted. Pen lift for time base adjusted.
00633 LKB 2138 Uvicord S, serial number 1332 Used in B.M.L.Sc. 2001-09 06 lubricated power switch; Craig D. of Phoenix Eq. observes that another make should not be substituted for the RCA RF oscillator transistor which excites the iodine or mercury vapour bulb.
00636 LKB 2138 Uvicord S, serial number 2110 Used in B.M.L.Sc. 2001-08 19 Replaced 470 microfarad capacitor in power supply. Old capacitor was orange; new is blue. 2001-09 06 lubricated power switch;
00638 Reichert-Jung Cryocut 1800.
00657 Bellco Glass Rocker Table Motor by RAE Corp., McHenry Illinois. 115 V DC, Serial or Model number 96257. Brushes, 0.25" x 0.25" x 0.5" long, spring attached. 2001-May 04, table dissassembled and cleaned, motor dissassembled and cleaned, gearbox opened, worm and bronze gear cleaned, commutator turned. Bearings of original size, 19 mm OD x 0.25" ID x 6 mm wide, not available. Order 0.75" OD x 0.25" ID x 0.25" wide for replacement---end plates of motor must be bored to accomodate. Case lined with felt to absorb sound. 2002 07 10 Brushes worn out. Replacements obtained from Bob's Electric Motors in Victoria.
00662 Superior Electric Powerstat Variable Autotransformer Type 116B. Input 120 V; output 0-140 V. 2002 10 16 Installed ground line and receptacle with ground. 2002 10 17 Overhauled switch to remove gummed grease. Returned to service in BMLSc.
00665 Sybron Thermolyne Mixer, Model number M-16715, Serial 2684147. 2002 05 03 Replaced deteriorated push switch with toggle switch.
00675 Mettler PC440 top loading balance, Serial 826671. 2004-09-01 Burning fuses. 2200 microF, 25 V cap. shorted. Capacitor replaced, housing cleaned, new shroud fitted and balance returned to BMLSc.
00679 Bio-Rad Model 500 Power Supply, Serial No. 28BR2325. This is the same model as tag number 00119. Go there for instructions. 2006 Inherited machine from D.E.B? 2007-07-31 The machine works. Please follow the Bio_Rad instructions, P.E.
00707 Sorvall MC12V Centrifuge, Serial No. 9503225. 2003-03-05 replaced 0.25 A fuse on interlock pcb. 2004-01-08 0.25 A fuse burned again. Fuse lasts O(10^2) hours. 2004-01-14 Mapped temperatures of components on interlock pcb in this machine and in 00524 for comparison. The SN75189, the smaller diode bridge and the adjacent relay are all a few degrees warmer in the machine which burns fuses. The pcbs were swapped between the two machines to locate the fault. [Tip: remove the two slot head machine screws and fold the interlock pcb outside the machine to allow observation during operation. The relay must be unplugged to allow the pcb out. Component temperatures were sensed with a Cole Parmer 39650-02. (nifty!) SN75189 Quadruple Line Receiver. Relay: 24VDC, 1/8 HP, 120 VAC, 5 A, 24 VDC, 120 VAC RES. Diode bridge: ??]
00801 GCA Precision Scientific VacTorr PV35 Pump Catalogue No. 10041, Serial No. 19-6396.
00811 Tissue-Tek III Wax Dispensing Console made by Sakura Fine Technical Co., Ltd., Tokyo. Model 4586 Serial No. 832102
00813 Shandon Hypercenter 2 Tissue Processor base unit. Cat. No. 66110166; Ser. No. BSB 4104/1/10N
2010-08-19 Replaced capacitor C16.
2012-12-04 Reassembled and reinstalled pump with newly wound coil.
00814 Hypercenter 2 console.
00901 Cigarette incinerater built by AWT. 2005-02-22-25 Trueing faces of valve plates, sealing fittings with Goop, trimming bolt slots, installing a 2nd setscrew on side of crank arm, reassembling and testing; 2006-10-11 Not running and, after changing the 555 chip, running continuously. With the contacts of the limit switch cleaned and the switch moved upwards on the chassis, the machine worked properly with the previous 555. Intake volumetric efficiencies: 80%, 80%, 80%, 80%, 85%.
00902 Cigarette burner built by AWT. 2004-08-31 Refitted with new valve. 2005-03-03-23 Trueing faces of valve plates, sealing fittings with Goop, reassembling and testing;
00903 Cigarette burner built by AWT. 2002 07 ?? Delivered to Pathology Department. 2002 09 06 Delay at syringe-closed position non-existent. 2002 09 20 Taken to Pender Island for repair.
00904 Cigarette burner built by AWT. 2005-03-23-2005-04- Disassembling valve, cleaning, trueing faces of valve plates, installing a 2nd setscrew on side of crank arm, reassembling and testing;
00905 Cigarette burner built by AWT.
00906 Cigarette burner built by AWT.
00907 Aqua-Pure AP1610 Filter on water feed to chiller in shared inst. rm. Aqua-Pure replacement filter, AP110, 5 micron. O-ring is 3.125" x 3.375" x .139", part number AP34737-13C, AR Thompson part 2-235. Allan F. reports that the main has a 15 micron filter. Incidently, the filter should be upstream of the Watts Pressure Regulator! 2002-02 Installed. 2002 09 27 Chiller down due to plugged filter. 2002 10 02 Hytrex II, GX05 - 9 7/8, 05 micron cartridge (Osmonics, Inc. Minnetonka, MN 612 933 2277, 1 800 848 1750) replaced with wound yarn filter from Plant Stores. Osmonics salesman recommends 5 or 10 micron. 2002 10 22 Another wound yarn filter from from Plant Stores installed. 2013-06-14 Filter replaced with Hytrex II, GX05 - 9 7/8, 10 micron.
00908 Watts 3/4" 009 M3 Reduced pressure zone backflow preventer. Should be tested annually by certified tester. 2002-02 Installed.
00909 Cart built from old EEG machine by Rolf. 2003-07-02 Turned over to Don B. laboratory.
00910 Cart built from old EEG machine by Rolf. 2003-08-19 Turned over to Dana D. laboratory.
00911 Small cart with S.S. top inherited from hospital. 2009-03-31 Turned over BMLSc.
00912 Heraeus Incubator; Model B5060 EK-CO2, Serial 9000483. 2009-06-10 New fan marked, System Papst, U.S. Pat. 3786290??, pat. pending, DBP ang., Impedence Protected, Made In Germany, TYP 900, 24-42 V ~ 50/60 Hz, 5,6 muF, Heraeus part 03750550
00941 Dominion Tape dispenser for packing tape. 2009-08-07 Indefinite loan to KBNF, Joc.L.
00942 Texas Instruments TI-82 calculator. 2009-10-28 Donated to Jen X. for B.M.L.Sc.
00943 Sony PSP, serial AT103157595-PSP3001. 2009-10-?? Purchased on eBay. Used for work.
00945 B&K Precision 20 MHz Digital Storage Oscilloscope, Model 2522, Serial 193-00438. ca. 1990 purchased new.
00946 Bostitch Type B5E6J Super-Duper Electric Stapler, serial no. 73943. Built in 1960s or '70s and still working well.
00947 Compaq Armada E500, serial no. 1J05FFM6M32K. Donated by Jody W.
00948 Regal 36 cup coffee urn. Donated to community use.
00949 Empire Supreme 32 cup coffee urn. Thermal switch replaced and donated to community use, 2011-12-16.
00950 CENCO ring stand, 18" column, grey base. Used by Cote staff to hold vacuum trap, Children's Hospital, 2013-05-21.
00951 Gordon McColb, Troubleshooting & Repairing VCRs, Second Edition. 2013-07-03 Long term loan to Bill F.
00952 Leitz REPRO 16707 Copy stand. 2013-10-18 Long term loan to Michael S.
00953 Extron VGA splitter. 2014-05-26 Installed in G221 by Anthony for use in summer course.
00954 Extron VGA splitter. 2014-06-10 Tested OK.
00955 Iomega AC adapter Model No. DA-30C01, P/N: 30941701. S/N: 449071530 Output 5 Vdc x 1.5 A, 12 Vdc x 1.5 A. used with Hitachi 500 GB USB drive. 2015-11-30 Made adapter for power plug and tested with Hitachi 500 GB USB drive.
00956 Wooden knife block. 2017-02-19 Refinished and placed in lunch room, G119.
00957 Rockwell Bag House Dust Extractor. Baldor Industrial Motor, now ABB (Allen Bradley/Baldor) Single Phase Cat. No. l1306 Spec. 35D11-68 Frame 56 Ser 778 H.P. 3/4 Volts 115-208/230 Amps 9.8/4.9 R.P.M. 3450 HZ 60 Class A Code K Full Load Eff. 62% P.F. 75% Rating 40 C AMB-CONT F Connection Low Voltage Line -1-3-8 Line -4-5-2 High Voltage 3-8-2 Not connected externally. Line -1 Line -4-5 Start Capacitor, Baldor 71300 485-540 MFD110/125 VAC 60 C Made in USA 2752
2018-03-07 Removed motor; removed end caps and cleaned out dust. Cleaned internal start switch contacts with emory paper.
00958 Hoover vacuum cleaner, green and black plastic. Model S1420, Bag type R, Serial No. 089900023078 1001 Nikon Model AFX, Serial number 141838 camera/microscope unit for control unit 1002. Cable is special. 28 pins all connected straight thru except that 3-4 are joined and connected with one conductor; 12 and 20 are open. The orginal cable was misplaced for a few years and a spare was made up during that time. The spare cable is longer and heavier and contacts 6 are not connected; seems to be a break in the conductor inside the cable.
1002 Nikon Model AFX, Serial number 141838 Control unit for camera/microscope unit 1001. Refer to note under 1001 about cable.
02015 Heat Systems Ultrasonics & Braunson, Sonifier Cell Disruptor Model W185E, Serial B8501188. 2002 02 12 Put into storage room contingent on use in Devine lab. or by new faculty.
02081 IEC Centra-M S.N. 2399R0122 2001-February, Diode bridge in power supply replaced, hinges galvanized.
2082 Remote control for Kodak carousel 2001 purchased.
02083 Remote control for Kodak carousel. 2001 February, purchased. 2001-03-13 Broken red wire at strain relief repaired.
02084 Pharmacia Peristaltic Pump P-3 Serial no. 112951. Inherited from ?? Original belt was 5 mm pitch x 5 mm w x 49 teeth. 2001-04-25 Drive belt replaced with 5 mm pitch x 6 mm w x 49 teeth, part T5-245-6. Purchased from Kaman Industrial Sales, Annacis, 523 2356, Joanne. 6.15 $ fob Edmonton, ~15 $ express shipping! Use parcel post next time.
02085 Mettler P3 top loading balance, serial number 325421. Purchased by Richard.H.P. (~1970? ). 2001-04-25 adjusted bulb, focus and mirror position and added mass to zero. Balance located in grn. lab. Manual in Mettler folder in workshop; Information for replacement of bulb. The extant bulb is marked "OSRAM GERMANY 91889 6 V 1,4 A cAZ". The base is a single contact bayonet style, 15 mm diameter. The bulb is 25 mm diameter. UAP/NAPA Auto Parts might find an inexpensive replacement. Also might substitute a Dr. Fischer 841002, base BA15S.
02086 Mettler P10N top loading balance, serial number 543902. Purchaser unknown. Balance located in gr. lab. 2001-04 26 adjusted bulb, focus and mirror position. Location of manual unknown.
02087 Sony Dictator BM-40A, serial number 10466; exterior cleaned, tested and issued to pmccowan.
02088 Steris Sterilizer Amsco Renaissance Remanufactured 3011 Gravity Sterilizer, 16" x 16" x 26". Serial Number 0184116-SAWU Vessel serial number R8104200-04 (3291) Steris Canada: 1 800 661 3937 Parts: x26212 Technical support: refer to Steris in desktop file. Amsco recommends replacing the safety valves annually. Leaking union downstream of check valve 2 in Figure 4, page 16, Illustrated Parts Breakdown, 1999 07 29, Rev. 5. 2001-03 29 Ref. no. 1201622. Ian M. to visit Tuesday, 2001-04 03. Never saw Ian. 2001-06 29 Ref. no. 1304971. Spoke to dispatcher Mark. He is to report problem to Ian again. 2001-07 05 Air inlet check valve replaced by Steris representative, Nolan T. Union on jacket flood line was leaking; cleaned faces and refitted. Air inlet filter should be changed at intervals of ~ 6 months. 2001-07 06 (10 air inlet filter elements. part no. 129360-802 ordered). Note that ESB Filtration Inc. wants 18.38 $/element. So much for 3rd party suppliers. 2002 01 27 air inlet filter changed. Trace quantity of dirt visible on old filter. 2003-02-04 steam leaking from safety valve on generator. 2003-02-05 Nolan T. replaced two safety valves, flushed generator, cleaned contact sensors in top of generator. Gave instructions for flushing generator at least once per week; preferably each day when machine is powered up. 2003-02-14 Call to Tech. Support, 800 333 8828, about dirty water spewing from sump when flushing boiler. Flushing at 10 psi rather than 20 psi recommended. ============================= 2004-07-21 Notes On Valves S2 3/8" steam to chamber solenoid valve P093910-650 331.80. Amsco repair kit no. P764317-687 121.45. RV1 1/2" 40 psi jacket safety valve, Spence Eng. 0041DCA-01-040. Amsco part number 1P150828-473 173.15. 1/2" 100 psi boiler safety valve, Conbraco 19KDCA100BA, Amsco part number P764323-459 161.95. Valve replacement and service Vaptec Inc. http://www.vaptec.ca/ 514 630 0390 Tyler Gratton Associate, Imperial Valve of Port Moody, B.C. 604-461-3438, Stanley. Sight glass assembly for boiler. Refer to pp. 48, 49 of _Amsco Eagle Series 3000 Gravity and Vacamatic Sterilizers_. Valves are Conbraco 250 SWP, male 1/2" NPT. Glass is 15 mm OD, 148 mm long. Calculated Length = center-center of valve spindles - 2" = 7+7/8"-2" = 5+7/8" = 149.2 mm. Price of pair of valves from local supplier. 2008-08-12 $197.98 =============================
2004-08-12 S2 valve rebuilt with Steris kit.
2004-09-30 Les found liquid cycle not terminating.
Spoke to Mark at tech. support. Close steam supply valve
on top panel. When gages drop to ambient pressure, open
door carefully.
2006-03-01 Replaced door gasket. Cleaned gasket contact face.
Greased door locking rods.
2006-03-02 Malcolm Bishop, Provincial Safety Inspection Manager,
reported that provincial regulations do not specify a maximum
lifetime for safety valves. Check periodically for leakage.
2007-09-11 Safety valves tested. Boiler valve OK. Jacket valve
failed to open.
2007-09-13 Jacket safety valve replaced by Jim.
2008-07-18 Making and installing a better fitting s.s. compression
ring in a valve on the sight glass assembly.
2008-09-21 Repacking stem of upper valve on sight glass.
Making and installing new rubber tires in printer.
2008-10-30 Reinstalling sight glass with fresh rubber grommets.
2008-10-30 Installing a longer sight glass and testing for leaks.
2008-11-03 Repacking stems of both valves of sight glass.
2008-11-04 Turning s.s. ring in lower valve, refitting
teflon packing, heating boiler and checking for leaks
2009-01-22 Making and installing a sleeve to hold the core
of the paper take-up spool.
2009-04-16 Installing fresh paper.
2009-06-25 Reinstalling sight glass with another set of fresh seals.
2010-06-11 Installing fresh paper.
2010-06-15 Installing new seal on sight glass and heating boiler to test.
2010-07-27 Tightening compression nuts on sight glass.
2010-07-28 Replacing upper seal on sight glass.
2010-10-21 Replacing seals on sight glass;
2011-04-14 Replacing upper seal on sight glass,
cleaning chamber and drain screen, powering up to test.
2011-08-24 Organizing log sheets. Removing sight glass,
checking seals, reassembling.
2011-10-21 Installing fresh paper.
2011-11-04 Replacing upper seal on sight glass, powering,
flushing, checking for leaks.
2011-12-16 Untangling paper in printer.
2011-12-20 Untangling paper in printer.
2012-01-04 Reattaching paper to spool.
2012-01-13 Checking and adjusting settings.
2012-01-25 Adjusting paper guide.
2012-02-08 Adding table of parameters to sliding door
on control column.
2012-03-28 Resealing sight glass and installing fresh paper.
2012-05-22 Tightening compression nuts on sight glass.
2012-08-08 Begin monitoring liquid cycle to
understand problem at completion.
2012-11-29 Changing seal at top of sight glass and
heating boiler to test.
2013-01-03 Installing fresh paper. Making plastic collar
and refitting paper. Removing microswitch, reconfiguring
trigger, reassembling and testing printer.
2013-01-16 Readjusting sight glass seals.
2013-01-17 Resetting setscrew in spool and reattaching paper.
2013-01-25 Replacing switch on door lock, starting boiler to test.
2013-02-06 Adjusting sight glass and checking for leakage.
2013-02-26 Testing Teflon wrap on lower gasket as well as upper.
2013-02-27 Revising our operating instructions for users.
2013-03-01 Refitting the sight glass with Teflon coated
silicone at the top and black rubber at the bottom.
2013-03-07 Checking heater elements with ohmeter and reconnecting.
2013-03-08 Drilling small holes in outer corner of lower
door to allow water to drain.
2013-03-13 Removing low water cutoff probe, installing CLR.
2013-03-14 Draining CLR, monitoring sight glass, powering up to
fill boiler. Changed air inlet filter.
2013-03-20-22 Draining boiler, removing depth probes
and heater module, drying interior, cleaning, installing
new module, replacing probes, testing.
2013-03-27 Removing and disassembling printer, making and
installing new drive tires, reassembling and replacing
printer, installing wider paper;
2013-05-23 New safety valve installed on boiler by Aktor.
2013-07-26 Installing new sight glass assembly.
2013-07-31 Replacing upper seal on glass and packing on
upper valve stem.
2013-09-18,19 Removed shelf rack from chamber and cleaned.
2014-09-17 Valve S9 replaced with new. Sight glass gaskets tightened.
2015-09-15 Control relay replaced and S9 still whistling.
2015-09-15 Rebuild kit installed in S9; returned to quiet operation.
2016-03-18 Clock advanced about 9 minutes to correct time.
2016-07-20 Replaced leaking upper gasket ring with a used one.
Leaking again within 48 hours. 10 new gaskets ordered.
2016-07-29 Installed new gasket rings on sight glass and verified OK.
2017-03-15 Renewing gaskets on sight glass; powering for leak test.
2017-03-24 Printed roll of paper removed.
2018-12-08 Installed fresh paper tape.
2019-09-13 Reviewed replacement of gaskets on sight glass with J.X. and V.R.
Trimmed two openings in s.s. outer cover of door for clearance
of locking bars. Cleaned residue of old grease from inside of
cover. Applied fresh grease to door locking system. Found
replacement for missing screw and reinstalled cover.
2020-02-06 Rebuild kit for hi-low valve received from Steris.
2020-02-07 Valve removed and mostly dismantled. S.s. seat frozen.
2020-02-10 Valve seat removed with heat. Brass spacer disk made according to
instructions from Steris technical support.
2020-02-11 Valve reinstalled in machine and tests run. Temperature about
8 F low. Brass disk removed and another test gave satisfactory
temperatures.
2020-02-12 Several runs through the day with correct temperatures.
===== End of Sterilizer Maintenance Log ======
== Check list 2013-03-14 ==
Hot water supply, currently 62 psi.
Cold water supply, currently 75 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2013-09-19 ==
Hot water supply is currently 42 psi.
Cold water supply is currently 65 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2013-11-01 ==
Hot water supply is currently 60 psi.
Cold water supply is currently 65 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2014-01-15 ==
Hot water supply is currently 63 psi.
Cold water supply is currently 41 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2014-03-21 ==
Hot water supply is currently 48 psi.
Cold water supply is currently 40 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2014-09-19 ==
Hot water supply is currently 42 psi.
Cold water supply is currently 75 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2014-12-11 ==
Hot water supply currently 50 psi.
Cold water supply currently ~84 psi.
Chamber drain screen cleaned.
Air inlet filter ok.
Door gasket visually ok.
No steam or water leaks.
== End of Check list ==
== Check list 2015-03-24 ==
Hot water supply currently 45 psi.
Cold water supply currently ~84 psi.
Chamber drain screen cleaned.
Air inlet filter and lower O-ring replaced.
Door gasket visually ok.
No steam or water leaks, pending.
== End of Check list ==
== Check list 2015-11-17 ==
Hot water supply is currently 72 psi.
Cold water supply is fluctuating 75-85 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket ok.
No steam or water leaks.
== End of Check list ==
== Check list 2016-02-02 ==
Hot water supply is currently 62-63 psi.
Cold water supply is 84-85 psi.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket ok.
White scale around stems of sight glass valves.
Otherwise no steam or water leaks.
== End of Check list ==
== Check list 2016-09-06 ==
Hot water supply is currently 38-48 psi.
Cold water supply is 48 psi.
Lower pressures associated with draw of Heinicke washer.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket ok.
White scale around stems of sight glass valves.
Otherwise no steam or water leaks.
Paper tape printing ok.
== End of Check list ==
== Check list 2017-03-24 ==
Hot water supply is currently 48 psi.
Cold water supply is 80 psi.
Heinicke washer not in use.
Chamber drain screen clean.
Air inlet filter ok.
Door gasket ok.
White scale around stems of sight glass valves.
Otherwise no steam or water leaks.
Paper tape printing ok.
Safety valves not leaking.
== Check list 2018-01-18 ==
Hot water supply is currently 46 psi. Heinicke washer not in use.
Cold water supply is 84 psi.
Chamber drain screen cleaned.
Air inlet filter appears as new. Filter holder about 1/3 full of water. Filter replaced.
Door gasket ok.
White scale around stems of sight glass valves. Spare stem packing is in drawer.
Otherwise no steam or water leaks.
Paper tape printing well.
Check safety valves when boiler is hot.
== Check list 2018-04-04 ==
Hot water supply is currently 280 kPa = 40 psi. Heinicke washer not in use.
Cold water supply is 550 kPa = 84 psi.
Chamber drain screen, small bits of scale removed from bottom.
Air inlet filter appears as new. Filter holder about 1/4 full of water
after preceeding liquid cycle. Overhaul check valve. S2 leaking?
Door gasket ok.
White scale around stems of sight glass valves. Spare stem packing is in drawer.
No water leaking from sight glass.
Otherwise no steam or water leaks.
Paper tape printing well.
With boiler hot, both safety valves tested and found to close properly.
Flash cycle 2 operated as a test. Alarm occurred after 21 minutes;
pressure observed at 268 Fahrenheit. Diagnosis: Hi/Lo valve malfunctioning?
S2 leaking? See above.
Small leak in door gasket?
Hot water supply pressure dropping? Observe at end of flash cycle.
== Check list 2018-08-13 ==
Hot water supply currently 46 psi. Heinicke washer not in use.
Cold water supply is 81 psi.
Chamber drain screen, small bits of scale removed from bottom.
Air inlet filter appears as new. A few tablespoons of water in holder.
Inlet check valve removed. Should be cleaned. 9/16" or 14 mm 8 pt.
socket needed for removal.
Door gasket ok.
White scale around stems of sight glass valves.
No water leaking from sight glass.
Otherwise no steam or water leaks.
Paper tape printing well. Paper roll down to ~2 cm diameter.
Flash cycle 2 operated as a test. Alarm occurred with over-temperature,
273 degrees F, 3 degrees above target. Check Hi-Lo valve and adjust if necessary.
== Check list 2018-11-29 ==
Hot water supply currently 41 psi. Heinicke washer not in use.
Cold water supply is 78 psi.
Chamber drain screen, small bits of scale removed from bottom.
Air inlet filter appears as new. With machine cold, no water in holder.
Door gasket ok.
White scale around stems of sight glass valves.
No water leaking from sight glass.
Otherwise no steam or water leaks.
Paper tape printing well. More than half of paper roll remaining.
== Check list 2019-02-06 ==
Hot water supply currently 42 psi. Heinicke washer not in use.
Cold water supply is 45 psi. Pressure reducing valves were
adjusted since previous report.
Chamber drain screen, small bits of scale removed from bottom.
Air inlet filter appears as new. With machine cold, no water in holder.
Door gasket ok.
White scale around stems of sight glass valves.
~ a tablespoon of water from sight glass during run.
Otherwise no steam or water leaks.
Paper tape printing well. More than half of paper roll remaining.
== Check list 2020-02-12 ==
Hot water supply currently 41 psi.
Cold water supply is 86 psi. ** Adjustment required. **
Chamber drain screen, small bits of scale removed from bottom.
Air inlet filter appears as new. With machine cold, no water in holder.
Door gasket ok.
White scale around stems of sight glass valves.
No steam or water leaks.
Paper tape printing well. ~1/4 paper roll remaining.
== End of Check list ==
02089 Heinicke Instruments Laboratory Glassware Washer. Serial number 133079-49. Von Weise Gear Co., 100 St. Clair Industrial Park St., Clair MO 63077. Phone: 636 629 1010 http://www.fasco.com/ Nozzle transport motor, Model V00786AA11, Continuous Duty, Serial number F-78, 115 V, 1 amp., 1 phase, Thermally protected-L, 15 RPM output. Needle bearings on output shaft Kaydon KN-060904 2000-10-25 Replaced hose at back of washing chamber with 2 ft of 3/4" G311-075 purchased from Green Line Hose & Fittings, 3.20 $. 2001-07 12 Stainless steel roller bearing installed in pulley for cable in washing chamber. 2002-05-08 Replaced the two upper hoses in the back of the washing chamber.
02090 IKA MS1 Minishaker Serial ? *03.013323* Replaced broken drive belt with O-ring 2.5 mm x 286 mm. 2001-08-30 replaced O-ring again.
02091 MT-660A surge suppressing power bar.
02092 486 PC labelled C.H.U.R.G.3. 2001-08 22 located at the north side of morphometry room. 2001-08 22 Measure works with Summasketch (Pathology 02094) attached via serial port 1.
02093 Trison 486 PC. 2001-08 22 located at the south side of morphometry room. 2001-08 22 Measure works with Hipad (Path 02095) attached.
02094 SummaSketch Plus Digitizer. Model MM1201, Serial number *010170091820335108*. 2001-08 21 Measure worked with digitizer connected to PC in office of Jody W. 2001-08 24 Tablets, scanners and boards now dealt by GTCO 480 443 2414, http://www.gtcocalcomp.com/ 2001-09 06 Replaced yellow Omron switch on cursor with one donated by Eric Sorensen.
02095 Houston Instrument Hipad Digitizer with Bioquant chip. Model DT-11 Serial number 140180-10054. 2001-08 21 Measure worked with digitizer connected to PC in office of Jody W.
02096 Houston Instrument Hipad Digitizer. Model DT-11 Serial number 10551-13. 2001-08 21 Measure did not work with digitizer connected to PC in office of Jody W.
02097 TVM SuperSync 2A Color Monitor (VGA) 2001-08 28 Adjusted focus. Tested on 00282 PC.
02098 TekTator V Serological Rotator table; R4139-5 Serial 01778. American Hospital Supply, Evanston IL. Motor: Johnson Electric, Hong Kong. 2001-08 09 disassembled machine. 2001-08 19 opened motor and found brushes worn away and commutator worn down by springs. 2001-08 30 machined commutator. 2001-08 31 made new brushes and reassembled motor. 2002 07 20 repair by AW Technologies. 2003 06 25 Bushing in fiber gear disintegrated. New bushing made by R.M.
02099 JVC Color Video Camera TK-1070U Serial number 16750625 2001-09 05 External DC power supply repaired by Eric Sorensen, Media Group.
02100 6 outlet relocatable power tap.
02101 BraunSonic 1510 power supply and controls 2001-10 23 put in custody of Devine Lab, Elizabeth M.
02102 BraunSonic 1510 sonicator head. 2001-10 23 put in custody of Devine Lab, Elizabeth M.
02103 Clay Adams Dynac II centrifuge, catalog no, 0103, serial no. 168130. Motor: Jones Instrument, Stamford Connecticut, now owned by EAD Motors. "Punch-Line" Model 8240-108, 115 V AC-DC, Code FX. Brushes are part number MA-54-2RP. 2001-10 21 new brushes installed. Brushes sent by Dotty. Circuit schematic drawn and stored in shop file.
02104 Bausch & Lomb Spectronic 20 Colorimeter-Spectrophotometer Serial number: ND8122 Type: 33-29-61-64 2001-11 02 donated to Pender Island School.
02105 Manual for 02104 Bausch & Lomb Spectronic 20 above.
02106 HP LaserJet 5L 2001-11 02 in use by Vickie M. 2002 06 26 removed a sheet of acetate which was rolled around fuser drum.
02107 Small printer table with black steel frame & white top. 2001-11 02 in use by Vickie M.
02108 Logitec MD14 two button mouse
02109 Edwards Vacustat manometer 2001-11 18 Mercury fills measuring column and will not descend.
02110 Magnavox SuperVGA color monitor 2001-11 22 Sent to Research Pavillion for use by Niamh K.
02111 Genius GF-303 3 button mouse 2001-11 26 in use on king.
02112 AST keyboard SN: 50533605 2001-11 22 Sent to Research Pavillion for use by Niamh K.
02113 Logitech MouseMan, Serial Mouse Port, M-CJ13 2001-11 22 Sent to Research Pavillion for use by Niamh K.
02114 B&K Solid State Tube Tester Model 747
02115 Isabergs Verkstads stapler purchased from Dave Adams 2002 01 07.
02116, 02117, 02118, 02119 Hodges modular shelf unit made from wire, approximately 5' W x 2' D x 6' H.. 2002 01 10 stored with Graham D.
02120 HP Laserjet III model 33449A, serial no.: 2947J18317 2002 01 01 reporting "50 Service" on display; fuser cold; By swapping parts with another machine, located problem to fuser controller board RG1-1438 in power supply. Replaced C158 22 microfarad, 25 V with 22 microfarad, 50 V. Error message gone. Schematic of RG1-1438 posted to an HP user forum by Flemming Gottsche. To the best of my knowledge this machine was purchased by Don B. Consequent to the failure described, it was swapped with shop machine 02122. 2002 02 20 Swapped back to Johan's office consequent to failure of 02122. 2003-05-07 Dumbbell gear failed. Replaced primary gear train (SX motor drive gear assembly) with a used assembly from fixyourownprinter.com. 2006-04-21 Noisy machine; smudged output.
02121 YSI Model 46 Tele-thermometer with manuals & probes. 2002 02 07 Loaned to Lyle H.
02122 HP Laserjet III model 33449A, serial no.: 3104JE1747 Shop printer. 2002 02 20 Machine reporting "50 Service" error. Tweaked connector on laser beam detector as described here. http://fixyourownprinter.com/tweaking.html 2003 05 06 Added 4 MB memory board. 2004-01-16 Main board in AC power supply proved faulty by swapping with a working board. Component Equivalences TRIAC BCR8PM = BTA12-600C = NTE5645. Optoisolator Sharp S21MD4V = MOC3061 = MOC306X. Working again after replacement of triac.
02123 Forma Water Jacketted Incubator, Model 3326 Serial number 33287-392. 2002 01 brought from Ottawa by Ed P. 2002-02-06, 07, 08 bearings removed from motor & cleaned; leads extended to allow field winding to be reversed to obtain correct rotation for cetrifugal impeller.
02124 Dolly for compressed gas bottle. This came from Anaesthesia upstairs and was given to Ed P's lab.
02125 Fisher Junior Drying Oven. This is a steel cabinet about 30 cm w x 30 cm h x 25 cm d, painted metalic green. Probably made between 1950 and 1975. Don B. may have inherited it from Phil Vassar. 2002 03 01 Failed to heat. 2002 03 02-24 installed two new thermostats, and a new power cord before discovering the bulb socket shorted due to a perished insulating washer. Installed a new washer in the socket, new internal wiring, a third new thermostat and finally it worked. Remains operating in db lab. Purchased a package of bulbs and replaced the failed bulb. 2002 03 29 Oven failed again. This time it was simple --- The nut on the left stud attaching the center coil to the jumper was so corroded that the circuit was open. Replaced the nut and it worked again. 2003-10-23 Replace power cord with National Cable Specialists PolarFlex 40 14/3 SJOOW 90C CSA FT1. 2004-07-20 Replaced all internal wire with 14 ga GTF white from Rel. Parts. 2004-12-01 Internal wire failed again. Note temperature rating = 125 C. 2005-01-27 Replaced all internal wire with 1 m of 14 ga SEW from maintenance. This is rated at 200 C.
02126 Linear Instruments, Reno NV, Chart Recorder, Model 255, Serial 0055126. 2002 03 10 Replaced capacitor on power supply board for stepper motor which drives paper. Motor still does not operate. Submitted to Armature Electric for testing. Helpful information was received from Prof. Douglas Jones, U. of Iowa.
02127 LKB Peristaltic Pump, part number 90 01 1880, serial number 4321 2002 04 09 Rolf replaced one of the capacitors in the power supply. Turned over to Helen for BMLSc.
02128 White Instruments Inc. 4301 Spectral Filter. 2001-12 salvaged from audiology lab on 2nd floor. 2002 05 delivered to Pender Island Community Center.
02129 Hewlett Packard Model 200J Audio Sine Wave Generator. Formerly UBC Chemistry Number 667. 2002 05 Taken to Pender Island School.
02130 McCurdy Model AM403 Monitor Amplifier. Formerly UBC Chemistry Number 1643. 2002 05 Donated to Pender Island School.
02131 Blue M Gravity Convection Oven. 2002 05 16 Installed new Rebertshaw Thermostat (~120$). Good thermal stability!
02132 HP Laserjet III model 33449A, serial no.: 3227A05854 2002 04 28 Error message on LCD. Swapped AC power supply, fuser, 2 PCBs in lower chassis and front panel with working machine. Problem persists. DC p.s. is the only module untested. 2002 06 28 LCD reporting LOW TONER whereas Jody W. reported installing a new cartridge not long ago. Laser S. reports the empty weight of the cartridge is 1040 g; full weight is 1290 g. Cartridge giving the low toner report is 1104 g on 2002-07-10. There can be 64 g of toner in the waste chamber. Install a fresh cartridge weighing 1302 g and LCD reports READY. 2002 07 10 Machine returned to service.
02133 LKB 2138 Uvicord S, serial number 8822 Used in B.M.L.Sc. 2002 02 13 Purchased from SERF for 100$ inc. chart recorder.
02134 Bioquant II Houston Instrument Hipad Digitizer. Model DT-11 Serial number 128970-10041. 2003 05 23 In custody of Jody W.
????? Screen Machine frame grabber for ISA bus, V1.3 factory marked 1991 Mar 12 with FAST Electronic S-VHS Adapter V1.0 02.07.90. 2002 02 13 Color signal (chromitance) not being interpreted.
Set Blue M oven to 350 F for heating acrylic. Set Lab Line oven switch to low and dial to 30 for preheating toolset.
Small circular vessels Blanks: 3 mm thick x 195 mm square; ?? in stock. Backs: 6 mm thick x 145 mm square.
Medium circular vessels Blanks: 3 mm thick x 250 mm square; ?? in stock. Backs: 6 mm thick x 200 mm square.
Large circular vessels Blanks: 3 mm thick x 305 mm square; ?? in stock. Backs: 6 mm thick x 225 mm square.
Jumbo circular vessels Blanks: 3 mm thick x 356 mm square; ?? in stock. Backs: 6 mm thick x 300 mm square.
Small rectangular vessels Blanks: 3 mm thick x ?? mm x ?? mm; Backs: 6 mm thick ?? x ?? mm.
Medium rectangular vessels Blanks: 3 mm thick x 200 mm x 380 mm; Backs: 6 mm thick 120 x 300 mm.
Large rectangular vessels Blanks: 3 mm thick x 254 mm x 445 mm; Backs: 6 mm thick x {132-140} mm x 340 mm.
Large quasi-square vessels Blanks: 3 mm thick x 350 mm square; Backs: 6 mm thick x 300 mm square.
Aluminum
angle 0.75" x 0.75" x 0.125" x ~10' long. square tube 0.75" side x 0.125" wall x ~6 long. round bar 0.375" diameter x ~8' long. round bar 1" diameter x ~12' long, 2 pcs. round bar 1.5" diameter x ~6' long, 2 pcs. round bar 2" diameter x ~2.5' long. round bar 2" diameter x ~6' long.
Brass
round bar, 1.5" diameter x 10.5" long. round bar, 3" diameter x 10.5" long. 0.5" plate, 5" x 12".
Mild Steel
angle 1.45" x 1.45" x 0.125" x ~10' long. angle 2" x 2" x 0.180" x ~6' long. threaded rod, 0.625" UNC x ~6' long. plate 0.25" thick x 24" x 30".
Stainless Steel
Pipe, 312T-316 3/4" Sch 40 Welded HT 6516, approximately 1' long. Pipe, SMP TP304 WLD 3/4"NB x Sch40SX20, PA7-22224, approximately 10" long.
Round bar, 3/16" dia. ~6' long. Round bar, 0.25" dia. x ~10'long, 3 pcs. Round bar, 0.50" dia. x ~8' long. Round bar, 1" dia. x ~6' long, 3 pcs. Round bar, 1" dia. x ~7' long. Round bar, 1" dia. x ~8' long.
Tube 0.255" OD x 0.184" ID x 7' long.
Salem Tube Inc. 06/97 0.375" x 0.65" wall x 9' long. Type 316/316L SMLS HTH STD ASME-SA-213 ASTM-A-213 ASTM-A-269.